Start-Up
 
While hot tub is filling, add initial dose (375 ml per 1,000 L) of Dazzle™ Stain & Scale 1 to
cold water. Once full, start pump, operate with the aeration off and commence heating.
 
Bring a water sample to your Dazzle™ Retailer for water balance recommendations.
 
Balance water according to your Dazzle™ Retailer’s recommendations.
 
Allow water to circulate for 2 hours.
 
Apply Dazzle™ Amaze per label directions (2 caps per 1,000 L). Ensure that the pump and
filter are operating and leave the cover off for a minimum of one hour after application.
 
Allow water to circulate for at least 15 minutes before proceeding to next step.
 
Add initial dose of Dazzle™ Botanical Cleanse (3 caps per 1,000 L). Pour around the
edges of the hot tub with the pump operating and the aeration off. Avoid adding Dazzle™
 
Botanical Cleanse when the sanitizer level is above 5 ppm.
 
Apply chlorine or bromine to the hot tub. Use Dazzle™ Bromine Granules or Chlorine
 
Granules to initially establish the residual. Consult with your Dazzle™ Retailer to select the
sanitizer that best meets your needs. Achieve continuous level of 3.0 – 5.0 ppm.
 
Add initial dosage of Dazzle™ Performance Plus (200 g per 1,000 L). Apply through the
skimmer or in front of the suction plate with the pump in operation and the aeration off.
 
Add initial dosage of Dazzle™ Nature Sheen (20 ml per 1,000 L.). Apply with the pump in
operation and the aeration off. Run filter continuously until water clears. Dazzle™ Nature
 
Sheen will agglomerate particulate into masses large enough to be filtered out. Watch
filter closely and clean as required.
 
Daily
 
Test sanitizer and pH level with Dazzle™ Test Strips. Add Dazzle™ Bromine Granules or
Chlorine Granules to boost the sanitizer level should it fall below 3.0 ppm. Always
maintain the bromine/chlorine reading between 3.0 – 5.0 ppm. The pH level should be
maintained at 7.4 - 7.6.
 
Weekly

Add regular weekly dosage of Dazzle™ Stain & Scale 2 (1 cap per 1,000 L) to protect against metal staining and scale formation. Apply directly to water with pump operating and aeration off.

Oxidize water with Dazzle™ Amaze (2 caps per 1,000 L) by broadcasting over water surface.
Note: heavy bather load may require more frequent applications. Allow water to circulate for at least 15 minutes and leave the cover off for minimum 1 hour. Wait 15 minutes before moving to next step.

Digest and remove organics with Dazzle™ Botanical Cleanse (3 caps per 1,000 L). Add directly to water with pump operating and aeration off.
 
Add weekly dosage of:
Dazzle™ Performance Plus (6½ caps per 1,000 L).
Dazzle™ Nature Sheen (½ cap per 1,000 L).

Brush, skim and vacuum.

Clean water line with Dazzle™ Tub Cleanse, if necessary.
 
Monthly

Have water tested at your Dazzle™ Retailer. Adjust pH, total alkalinity, calcium hardness as required.

Clean cartridge with Dazzle™ Filter Cleanse as per label directions.
 
Draining

Clean entire hot tub including plumbing lines with Dazzle™ Drain Prep. Add as per label directions the day before draining.

Drain hot tub and clean surfaces with Dazzle™ Tub Cleanse.

Clean cartridge with Dazzle™ Filter Cleanse as per label directions.

Clean cover with Dazzle™ Cover Cleanse & Protect as per label directions.